- default_value-1Value to return if target value is not found on line and error_if_not_found is false.
Default:-1
C++ Type:double
Unit:(no unit assumed)
Controllable:No
Description:Value to return if target value is not found on line and error_if_not_found is false.
- depth36Maximum number of bisections to perform.
Default:36
C++ Type:unsigned int
Unit:(no unit assumed)
Controllable:No
Description:Maximum number of bisections to perform.
- end_pointEnd point of the sampling line.
C++ Type:libMesh::Point
Unit:(no unit assumed)
Controllable:No
Description:End point of the sampling line.
- error_if_not_foundTrueIf true, stop with error if target value is not found on the line. If false, return default_value.
Default:True
C++ Type:bool
Unit:(no unit assumed)
Controllable:No
Description:If true, stop with error if target value is not found on the line. If false, return default_value.
- execute_onTIMESTEP_ENDThe list of flag(s) indicating when this object should be executed. For a description of each flag, see https://mooseframework.inl.gov/source/interfaces/SetupInterface.html.
Default:TIMESTEP_END
C++ Type:ExecFlagEnum
Unit:(no unit assumed)
Controllable:No
Description:The list of flag(s) indicating when this object should be executed. For a description of each flag, see https://mooseframework.inl.gov/source/interfaces/SetupInterface.html.
- prop_getter_suffixAn optional suffix parameter that can be appended to any attempt to retrieve/get material properties. The suffix will be prepended with a '_' character.
C++ Type:MaterialPropertyName
Unit:(no unit assumed)
Controllable:No
Description:An optional suffix parameter that can be appended to any attempt to retrieve/get material properties. The suffix will be prepended with a '_' character.
- start_pointStart point of the sampling line.
C++ Type:libMesh::Point
Unit:(no unit assumed)
Controllable:No
Description:Start point of the sampling line.
- targetTarget value to locate.
C++ Type:double
Unit:(no unit assumed)
Controllable:No
Description:Target value to locate.
- tol1e-10Stop search if a value is found that is equal to the target with this tolerance applied.
Default:1e-10
C++ Type:double
Unit:(no unit assumed)
Controllable:No
Description:Stop search if a value is found that is equal to the target with this tolerance applied.
- use_interpolated_stateFalseFor the old and older state use projected material properties interpolated at the quadrature points. To set up projection use the ProjectedStatefulMaterialStorageAction.
Default:False
C++ Type:bool
Unit:(no unit assumed)
Controllable:No
Description:For the old and older state use projected material properties interpolated at the quadrature points. To set up projection use the ProjectedStatefulMaterialStorageAction.
- vVariable to inspect
C++ Type:std::vector<VariableName>
Unit:(no unit assumed)
Controllable:No
Description:Variable to inspect
FindValueOnLine
The FindValueOnLine Postprocessor is for sampling a line through a mesh or on a boundary looking for the point at which a specific value occurs. The values of the line must behave monotonically or an indeterminate solution may be found.
Find a specific target value along a sampling line. The variable values along the line should change monotonically. The target value is searched using a bisection algorithm.
Input Parameters
- allow_duplicate_execution_on_initialFalseIn the case where this UserObject is depended upon by an initial condition, allow it to be executed twice during the initial setup (once before the IC and again after mesh adaptivity (if applicable).
Default:False
C++ Type:bool
Unit:(no unit assumed)
Controllable:No
Description:In the case where this UserObject is depended upon by an initial condition, allow it to be executed twice during the initial setup (once before the IC and again after mesh adaptivity (if applicable).
- control_tagsAdds user-defined labels for accessing object parameters via control logic.
C++ Type:std::vector<std::string>
Unit:(no unit assumed)
Controllable:No
Description:Adds user-defined labels for accessing object parameters via control logic.
- enableTrueSet the enabled status of the MooseObject.
Default:True
C++ Type:bool
Unit:(no unit assumed)
Controllable:Yes
Description:Set the enabled status of the MooseObject.
- execution_order_group0Execution order groups are executed in increasing order (e.g., the lowest number is executed first). Note that negative group numbers may be used to execute groups before the default (0) group. Please refer to the user object documentation for ordering of user object execution within a group.
Default:0
C++ Type:int
Unit:(no unit assumed)
Controllable:No
Description:Execution order groups are executed in increasing order (e.g., the lowest number is executed first). Note that negative group numbers may be used to execute groups before the default (0) group. Please refer to the user object documentation for ordering of user object execution within a group.
- force_postauxFalseForces the UserObject to be executed in POSTAUX
Default:False
C++ Type:bool
Unit:(no unit assumed)
Controllable:No
Description:Forces the UserObject to be executed in POSTAUX
- force_preauxFalseForces the UserObject to be executed in PREAUX
Default:False
C++ Type:bool
Unit:(no unit assumed)
Controllable:No
Description:Forces the UserObject to be executed in PREAUX
- force_preicFalseForces the UserObject to be executed in PREIC during initial setup
Default:False
C++ Type:bool
Unit:(no unit assumed)
Controllable:No
Description:Forces the UserObject to be executed in PREIC during initial setup
- outputsVector of output names where you would like to restrict the output of variables(s) associated with this object
C++ Type:std::vector<OutputName>
Unit:(no unit assumed)
Controllable:No
Description:Vector of output names where you would like to restrict the output of variables(s) associated with this object
- use_displaced_meshFalseWhether or not this object should use the displaced mesh for computation. Note that in the case this is true but no displacements are provided in the Mesh block the undisplaced mesh will still be used.
Default:False
C++ Type:bool
Unit:(no unit assumed)
Controllable:No
Description:Whether or not this object should use the displaced mesh for computation. Note that in the case this is true but no displacements are provided in the Mesh block the undisplaced mesh will still be used.